| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix BPF_F_CPU validation for sparse CPU IDs
BPF_F_CPU stores the target CPU ID in the upper 32 bits of the map
operation flags. bpf_map_check_op_flags() currently compares that ID
with num_possible_cpus(), which is the number of possible CPUs rather
than a bound on CPU IDs.
On an arm64 QEMU guest with a CPU device-tree hole, the possible CPU
mask was 0,2-3. A userspace program using raw bpf() syscalls creates
a BPF_MAP_TYPE_PERCPU_ARRAY and performs update and lookup operations
for each CPU by setting BPF_F_CPU and the CPU ID in the flags.
With the old check, CPU 1 is incorrectly accepted while valid CPU 3 is
rejected with -ERANGE. The CPU 1 update then reaches the per-CPU map
access path and triggers:
Unable to handle kernel paging request at virtual address ...
pc : __pi_memcpy_generic+0x5c/0x22c
lr : bpf_percpu_array_update+0x2dc/0x2e8
Call trace:
__pi_memcpy_generic
bpf_map_update_value
map_update_elem
__sys_bpf
Check the CPU ID against nr_cpu_ids and cpu_possible() instead. This
rejects CPU IDs outside the valid range and CPUs absent from the
possible mask, while allowing valid sparse CPU IDs. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hsr: free learned nodes on device setup failure
hsr_dev_finalize() can fail after a lower-device RX handler has
already been registered (slave A is added before the failable slave B
and interlink adds). RX handlers run in softirq regardless of the
master's state, so frames received in that window can learn dynamic
nodes into node_db, and the error unwind never releases them.
Free both owned dynamic databases in the unwind, mirroring
hsr_dellink(). proxy_node_db is provably empty on every current error
exit (only interlink RX feeds it, and the interlink add is the last
failable step) and is freed for symmetry. The order is safe:
hsr_del_port() unregisters each RX handler with synchronize_net()
before hsr_del_nodes() runs, which removes remaining entries with
list_del_rcu() and defers their release with call_rcu() for readers
already under RCU. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx4: Fix mis-use of RCU in mlx4_srq_event()
Sashiko points out the radix_tree itself is RCU safe, but nothing ever
frees the mlx4_srq struct with RCU, and it isn't even accessed within the
RCU critical section. It also will crash if an event is delivered before
the srq object is finished initializing.
Use the spinlock since it isn't easy to make RCU work, use
refcount_inc_not_zero() to protect against partially initialized objects,
and order the refcount_set() to be after the srq is fully initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix unsafe xarray access in implicit ODP handling
__xa_store() and __xa_erase() were used without holding the proper lock,
which led to a lockdep warning due to unsafe RCU usage. This patch
replaces them with xa_store() and xa_erase(), which perform the necessary
locking internally.
=============================
WARNING: suspicious RCPU usage
6.14.0-rc7_for_upstream_debug_2025_03_18_15_01 #1 Not tainted
-----------------------------
./include/linux/xarray.h:1211 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by kworker/u136:0/219:
at: process_one_work+0xbe4/0x15f0
process_one_work+0x75c/0x15f0
pagefault_mr+0x9a5/0x1390 [mlx5_ib]
stack backtrace:
CPU: 14 UID: 0 PID: 219 Comm: kworker/u136:0 Not tainted
6.14.0-rc7_for_upstream_debug_2025_03_18_15_01 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_ib_page_fault mlx5_ib_eqe_pf_action [mlx5_ib]
Call Trace:
dump_stack_lvl+0xa8/0xc0
lockdep_rcu_suspicious+0x1e6/0x260
xas_create+0xb8a/0xee0
xas_store+0x73/0x14c0
__xa_store+0x13c/0x220
? xa_store_range+0x390/0x390
? spin_bug+0x1d0/0x1d0
pagefault_mr+0xcb5/0x1390 [mlx5_ib]
? _raw_spin_unlock+0x1f/0x30
mlx5_ib_eqe_pf_action+0x3be/0x2620 [mlx5_ib]
? lockdep_hardirqs_on_prepare+0x400/0x400
? mlx5_ib_invalidate_range+0xcb0/0xcb0 [mlx5_ib]
process_one_work+0x7db/0x15f0
? pwq_dec_nr_in_flight+0xda0/0xda0
? assign_work+0x168/0x240
worker_thread+0x57d/0xcd0
? rescuer_thread+0xc40/0xc40
kthread+0x3b3/0x800
? kthread_is_per_cpu+0xb0/0xb0
? lock_downgrade+0x680/0x680
? do_raw_spin_lock+0x12d/0x270
? spin_bug+0x1d0/0x1d0
? finish_task_switch.isra.0+0x284/0x9e0
? lockdep_hardirqs_on_prepare+0x284/0x400
? kthread_is_per_cpu+0xb0/0xb0
ret_from_fork+0x2d/0x70
? kthread_is_per_cpu+0xb0/0xb0
ret_from_fork_asm+0x11/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: eir: Fix possible crashes on eir_create_adv_data
eir_create_adv_data may attempt to add EIR_FLAGS and EIR_TX_POWER
without checking if that would fit. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio: break and reset virtio devices on device_shutdown()
Hongyu reported a hang on kexec in a VM. QEMU reported invalid memory
accesses during the hang.
Invalid read at addr 0x102877002, size 2, region '(null)', reason: rejected
Invalid write at addr 0x102877A44, size 2, region '(null)', reason: rejected
...
It was traced down to virtio-console. Kexec works fine if virtio-console
is not in use.
The issue is that virtio-console continues to write to the MMIO even after
underlying virtio-pci device is reset.
Additionally, Eric noticed that IOMMUs are reset before devices, if
devices are not reset on shutdown they continue to poke at guest memory
and get errors from the IOMMU. Some devices get wedged then.
The problem can be solved by breaking all virtio devices on virtio
bus shutdown, then resetting them. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: hyperv_fb: Allow graceful removal of framebuffer
When a Hyper-V framebuffer device is unbind, hyperv_fb driver tries to
release the framebuffer forcefully. If this framebuffer is in use it
produce the following WARN and hence this framebuffer is never released.
[ 44.111220] WARNING: CPU: 35 PID: 1882 at drivers/video/fbdev/core/fb_info.c:70 framebuffer_release+0x2c/0x40
< snip >
[ 44.111289] Call Trace:
[ 44.111290] <TASK>
[ 44.111291] ? show_regs+0x6c/0x80
[ 44.111295] ? __warn+0x8d/0x150
[ 44.111298] ? framebuffer_release+0x2c/0x40
[ 44.111300] ? report_bug+0x182/0x1b0
[ 44.111303] ? handle_bug+0x6e/0xb0
[ 44.111306] ? exc_invalid_op+0x18/0x80
[ 44.111308] ? asm_exc_invalid_op+0x1b/0x20
[ 44.111311] ? framebuffer_release+0x2c/0x40
[ 44.111313] ? hvfb_remove+0x86/0xa0 [hyperv_fb]
[ 44.111315] vmbus_remove+0x24/0x40 [hv_vmbus]
[ 44.111323] device_remove+0x40/0x80
[ 44.111325] device_release_driver_internal+0x20b/0x270
[ 44.111327] ? bus_find_device+0xb3/0xf0
Fix this by moving the release of framebuffer and assosiated memory
to fb_ops.fb_destroy function, so that framebuffer framework handles
it gracefully.
While we fix this, also replace manual registrations/unregistration of
framebuffer with devm_register_framebuffer. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Fix the page details for the srq created by kernel consumers
While using nvme target with use_srq on, below kernel panic is noticed.
[ 549.698111] bnxt_en 0000:41:00.0 enp65s0np0: FEC autoneg off encoding: Clause 91 RS(544,514)
[ 566.393619] Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI
..
[ 566.393799] <TASK>
[ 566.393807] ? __die_body+0x1a/0x60
[ 566.393823] ? die+0x38/0x60
[ 566.393835] ? do_trap+0xe4/0x110
[ 566.393847] ? bnxt_qplib_alloc_init_hwq+0x1d4/0x580 [bnxt_re]
[ 566.393867] ? bnxt_qplib_alloc_init_hwq+0x1d4/0x580 [bnxt_re]
[ 566.393881] ? do_error_trap+0x7c/0x120
[ 566.393890] ? bnxt_qplib_alloc_init_hwq+0x1d4/0x580 [bnxt_re]
[ 566.393911] ? exc_divide_error+0x34/0x50
[ 566.393923] ? bnxt_qplib_alloc_init_hwq+0x1d4/0x580 [bnxt_re]
[ 566.393939] ? asm_exc_divide_error+0x16/0x20
[ 566.393966] ? bnxt_qplib_alloc_init_hwq+0x1d4/0x580 [bnxt_re]
[ 566.393997] bnxt_qplib_create_srq+0xc9/0x340 [bnxt_re]
[ 566.394040] bnxt_re_create_srq+0x335/0x3b0 [bnxt_re]
[ 566.394057] ? srso_return_thunk+0x5/0x5f
[ 566.394068] ? __init_swait_queue_head+0x4a/0x60
[ 566.394090] ib_create_srq_user+0xa7/0x150 [ib_core]
[ 566.394147] nvmet_rdma_queue_connect+0x7d0/0xbe0 [nvmet_rdma]
[ 566.394174] ? lock_release+0x22c/0x3f0
[ 566.394187] ? srso_return_thunk+0x5/0x5f
Page size and shift info is set only for the user space SRQs.
Set page size and page shift for kernel space SRQs also. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: use the DMA API for resource backing on Xen
On a Xen PV domain page addresses bear no relation to the real machine
addresses the host would have to use to reach it.
virtio_ring.c handles this correctly, vring_use_map_api() returns true
for any xen_domain() regardless of VIRTIO_F_ACCESS_PLATFORM.
virtio-gpu makes the same decision independently, but its copy
looks only at the feature bit:
bool use_dma_api = !virtio_has_dma_quirk(vgdev->vdev);
QEMU does not set iommu_platform on virtio-vga by default, so
VIRTIO_F_ACCESS_PLATFORM is not negotiated, use_dma_api is false, and
virtio_gpu_object_shmem_init() describes the framebuffer's backing pages
to the host with sg_phys(). Those are guest-physical addresses. In a PV
domain they resolve, on the host side, to pages belonging to some other
domain, so the host scans out unrelated memory.
Move the decision into virtio_gpu_use_dma_api() and give it the
xen_domain() check, like vring_use_map_api() has. This
additionally enables the dma_sync_sgtable_for_device() calls in
virtgpu_vq.c, which are required for correctness whenever swiotlb
is in play.
Reproduced with a Xen 4.21 PV dom0 nested inside QEMU 8.2 with
virtio-vga, on both a distro 6.8 kernel and 6.18 LTS. A PVH dom0
works fine and doesn't need this fix because it is identity-mapped,
only PV dom0s are affected. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: prevent path traversal bypass by restricting caseless retry
ksmbd_vfs_path_lookup() enforces LOOKUP_BENEATH to restrict path
resolution within the share root. When a crafted path attempts to
escape the share boundary using parent-directory components ('..'),
vfs_path_parent_lookup() detects this and immediately fails,
returning -EXDEV.
However, a bug exists in __ksmbd_vfs_kern_path() under caseless mode.
The function fails to intercept the -EXDEV error and erroneously
falls through to the caseless retry logic, which is intended only
for genuinely missing files. During this retry process, the path
is reconstructed, leading to an unintended LOOKUP_BENEATH bypass
that allows write-capable users to create zero-length files or
directories outside the exported share.
Fix this by ensuring that the execution only proceeds to the caseless
lookup retry when the error is specifically -ENOENT. Any other errors,
such as -EXDEV from a path traversal attempt, must be returned immediately. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: use opener credentials for ADS I/O
Alternate data streams are stored as xattrs. Unlike regular file I/O,
their read and write paths therefore call VFS xattr helpers which recheck
inode permissions and LSM policy using the current task credentials.
Run ADS I/O with the credentials captured when the SMB handle was opened. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate NTLMv2 response before updating session key
ksmbd_auth_ntlmv2() derives the NTLMv2 session key into
sess->sess_key before it verifies the NTLMv2 response.
ksmbd_decode_ntlmssp_auth_blob() then continues into KEY_XCH even
when ksmbd_auth_ntlmv2() failed.
With SMB3 multichannel binding, the failed authentication operates on
an existing session and the session setup error path does not expire
binding sessions. A client can send a binding session setup with a
bad NT proof and KEY_XCH and still modify sess->sess_key before
STATUS_LOGON_FAILURE is returned.
Relevant path:
smb2_sess_setup()
-> conn->binding = true
-> ntlm_authenticate()
-> session_user()
-> ksmbd_decode_ntlmssp_auth_blob()
-> ksmbd_auth_ntlmv2()
-> calc_ntlmv2_hash()
-> hmac_md5_usingrawkey(..., sess->sess_key)
-> crypto_memneq() returns mismatch
-> KEY_XCH arc4_crypt(..., sess->sess_key, ...)
-> out_err without expiring the binding session
Derive the base session key into a local buffer and copy it to
sess->sess_key only after the proof matches. Return immediately on
authentication failure so KEY_XCH is only processed after successful
authentication. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: fix chown/chgrp with SMB3 POSIX Extensions
Ownership (chown) and group (chgrp) modifications were being ignored when
mounting with SMB3 POSIX Extensions unless CIFS_MOUNT_CIFS_ACL or
CIFS_MOUNT_MODE_FROM_SID were also explicitly set.
Fix this by checking for posix_extensions in cifs_setattr_nounix() when
updating UID and GID, ensuring that id_mode_to_cifs_acl() is called to map
and set the ownership/group information on the server. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (lm90) Add lock protection to lm90_alert
Sashiko reports:
lm90_alert() executes in the smbus alert context and calls
lm90_update_confreg() to disable the hardware alert line, without
acquiring hwmon_lock.
Concurrently, sysfs write operations (such as lm90_write_convrate) hold
the hwmon_lock, temporarily modify data->config, and then restore it.
If an alert interrupt occurs concurrently with a sysfs write, the sysfs
path will overwrite the alert handler's modifications to data->config
and the hardware register.
This unintentionally re-enables the hardware alert line while the alarm is
still active, causing an interrupt storm.
Add the missing lock to lm90_alert() to solve the problem. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix zeropoint update where i_size > remote_i_size
Fix the update of the zero point[*] by netfs_release_folio() when there is
uncommitted data in the pagecache beyond the folio being released but the
on-server EOF is in this folio (ie. i_size > remote_i_size). The update
needs to limit zero_point to remote_i_size, not i_size as i_size is a local
phenomenon reflecting updates made locally to the pagecache, not stuff
written to the server. remote_i_size tracks the server's i_size.
[*] The zero point is the file position from which we can assume that the
server will just return zeros, so we can avoid generating reads.
Note that netfs_invalidate_folio() probably doesn't need fixing as
zero_point should be updated by setattr after truncation or fallocate.
Found with:
fsx -q -N 1000000 -p 10000 -o 128000 -l 600000 \
/xfstest.test/junk --replay-ops=junk.fsxops
using the following as junk.fsxops:
truncate 0x0 0x1bbae 0x82864
write 0x3ef2e 0xf9c8 0x1bbae
write 0x67e05 0xcb5a 0x4e8f6
mapread 0x57781 0x85b6 0x7495f
copy_range 0x5d3d 0x10329 0x54fac 0x7495f
write 0x64710 0x1c2b 0x7495f
mapread 0x64000 0x1000 0x7495f
on cifs with the default cache option.
It shows read-gaps on folio 0x64 failing with a short read (ie. it hits
EOF) if the FMODE_READ check is commented out in netfs_perform_write():
if (//(file->f_mode & FMODE_READ) ||
netfs_is_cache_enabled(ctx)) {
and no fscache. This was initially found with the generic/522 xfstest. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate SID in parent security descriptor during ACL inheritance
Introduce smb_validate_ntsd_sid() helper to safely validate Owner SID
and Group SID inside the NT Security Descriptor (smb_ntsd) retrieved
from the parent directory. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ebtables: move to two-stage removal scheme
Like previous patches for x_tables, follow same pattern in ebtables.
We can't reuse xt helpers: ebt_table struct layout is incompatible.
table->ops assignment is now done while still holding the ebt mutex
to make sure we never expose partially-filled table struct. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bridge: eb_tables: close module init race
sashiko reports for unrelated patch:
Does the core ebtables initialization in ebtables.c suffer from a similar race?
Once nf_register_sockopt() completes, the sockopts are exposed globally.
sockopt has to be registered last, just like in ip/ip6/arptables. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: module: call ethnl_ops_complete() on module flash errors
When validate() fails we are skipping over ethnl_ops_complete()
even tho we already called ethnl_ops_begin(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: always recover the gpu
Previously, in case there was no more work to do, recover worker
wouldn't trigger recovery and would instead rely on the gpu going to
sleep and then resuming when more work is submitted.
Recover_worker will first increment the fence of the hung ring so, if
there's only one job submitted to a ring and that causes an hang, it
will early out.
There's no guarantee that the gpu will suspend and resume before more
work is submitted and if the gpu is in a hung state it will stay in that
state and probably trigger a timeout again.
Just stop checking and always recover the gpu.
Patchwork: https://patchwork.freedesktop.org/patch/704066/ |
